The control table is the main control for almost all of your GENERAL ELECTRIC washer? s capabilities. The switches, calls, and knobs most connect to the particular control board. In https://ulsterappliancerepair.com shorts out or gets broken, your machine will start to shed functionality or can stop working entirely. Models with a digital readout could also screen an error computer code telling you if the control board has stopped working. If you like fixing your own appliances, this can be a restoration you can make yourself. Order replacement part #WH12X10468 intended for most GE washing machine models. Then follow these steps in order to uninstall and replace the old control board.
Unplug the particular washing machine.
This can be the first step to any appliance fix project. When you have recognized what? s incorrect with your washer, make sure a person unplug it completely so you stay safe from electrical discharge and shock.
Take apart the washer.
Draw the washer away from wall. You only need enough place to slide the particular top access screen back. If you have room, try to pull the particular washer away from the wall as little as achievable therefore you don? capital t need to detach the particular hoses or switch off the.
Get rid of the three screws along the returning edge of the particular top access screen and the a few screws along the back side of the lean next to the management panel. Then you can take the top screen an inch back, which loosens the particular hold on the particular front trim piece. Carefully pry typically the trim clear of typically the tabs make this aside. Lift the top panel? s back edge way up and then set the full panel aside.
Take away the control screen next. To start out, draw out the detergent drawer in the left-hand side and even depress the clip in the back of the drawer in order to remove it entirely. Set it aside. Remove the twist next to the detergent drawer housing. Next, remove the particular screws along typically the back of the control panel gaming system. Also, pry upwards the top border of the gaming console to loosen the particular control panel. Maintain onto the management panel and click the two fastening an eye on the back again of the console inside the machine. Once it comes free, don? capital t pull it apart or let it slide. Instead, tilt this down to help you commence to unplug the wires.
You may need to disconnect all of the wire harnesses attached to the handle panel. All you have to perform is press straight down the tab to each plug. You wear? t have in order to worry about mixing up them up during reinstallation because each and every plug has the unique shape. On the other hand, should you? re nervous about working together with wiring, require a picture from multiple angles so you have a very visual guide of where each wire funnel should go.
When the control panel is completely detached through the washing machine, move it to a work surface. This is typically the part that properties the control panel.
Remove the older control board.
Leave the control section face down. Eliminate the screws together the perimeter from the control board. There ought to be four. Also, depress the locking navigation bars along the edge with the control table closest the winding edge of the control panel. Place be difficult to reach, so use a flathead screwdriver to move typically the tabs. Pull typically the control board away and shift the particular control panel away.
Flip the control board over. Take a picture associated with all the switches in the front part of the control board which means you have a new visual guide throughout reinstallation. Then commence removing each of the keys and assemblies and so you can maneuver them over to the new element. They should become relatively loose, so don? t implement too much power on the slim plastic parts.
Install the new control board.
Prior to deciding to put typically the new control panel part in the management panel console, mount all of the buttons you eliminated from the older part. The more time assemblies will usually have hooks that really must be slid into the cutouts on typically the control board to be able to provide extra stability. Make sure each of the control keys is installed so they match the image guide.
Once typically the buttons are generally inside place, pick upward the control panel and tilt that so it? s almost perpendicular to the ground. Get in line the particular control board? s i9000 shaft together with the opening in the control panel. As you do so, wiggle the particular knob somewhat and so the shaft aligns with the pit and snaps completely into place. The particular control panel helps hold the buttons inside place, but in case you tilt the control board too far forward within this step, some regarding the buttons might come loose. in case anything falls misplaced, just reinsert the hooks and try again.
Once the control board canal is within place, carefully keep both pieces held together and set the control panel face down. Now you can easily lock the two items together by softly pressing the three securing tabs into place and retightening the four screws all-around the edge from the control board.
Reassemble the washer.
Initially, orient the handle board assembly beside the top associated with the front regarding the washer and so the curved edge will be closest to typically the machine. Start inserting the wire wirings into the command board by using the style guide or even by matching every single wire harness to be able to the correct put.
Next, tilt typically the control panel backup so it? h flush with typically the top front associated with the washer, and make sure none of the wires get pinched. Slide the navigation bars along the bottom into the slot machine games on the right nook, and snap the particular the control panel into location. After that, retighten typically the screw that is located beside the soap drawer housing. Also, retighten the anchoring screws across the back regarding the control panel. Next slide the detergent drawer into location and reattach the particular top access section. If you look at the underside with the top accessibility panel, you? lmost all notice slots with regard to the circular hooks along the track. The pins need to go through the much larger end of the cutout and so the -panel lies flat and even then, when you slide the screen forward, lock in to place against the smaller area of typically the cutout. This part can be difficult, so an image guide like at the end regarding this video might help.
To do this, established the top accessibility panel carefully over the frame as well as the pins. It have to hand approximately an inch off typically the back. Before a person slide the screen forward, press typically the trim into location on the three securing tabs. Then slide the panel forward and add again all six screws to hold it in place.
Push your washer back straight into place and plug it in. Stick to the guide that came with the control board in order to program the cleaner. Each model provides a different step. Once your washer provides been programmed, that? s willing to start a new routine.